Elation COLOR SPOT 150 User Manual

USER MANUALVersion 1.0Keep this manual for future needs !© CopyrightReproduction prohibited !COLOR SPOT 150

10Fixation via the Omega holders1. Screw each clamp (1) to the included Omega holders (4) with M12 bolt and nut through the hole in the holder.2. Ins

114.6 DMX- 512 connection, master/slave connectionThe wires must not come into contact with each other, otherwisethe fixtures will not work at all, or

125. DMX Protocol-16 bit Mode 1 Mode 2 Value Function Type of control Channel Channel1 1 Pan0-255 Pan movement by 530° proportional2 3 Tilt0-25

13 Channel Channel8 8 Rotating gobo rotation 0-127 Gobo rotation proportional 128-189 Forwards gobo rotation from fast to slow proportiona

14Mode 3 Mode 4 Value Function Type of controlChannel Channel1 1 Pan0-255 Pan movement by 530° proportional2 2 Tilt0-255 Tilt movement by 28

15 Channel Channel7 6 Shutter,Strobe,Reset0- Shutter closed step 1-63 Light intensity from 0 to 100% proportional 64-95 Shutter open st

16The COLOR SPOT 150 can be operated with a controller in controller mode or without the controller in stand-alone mode.Both modes are described in t

178. Stand - alone modeThe fixtures on a data link are not connected to the controller but can execute pre-set programs which can bedifferent for ever

189. Functions of the control panelThe control panel situated on the front side of the base offers several features. You can simply set the DMXaddres

19Note:Disconect the fixtures from the DMX controller before master/slave operating ,otherwise data collisions canoccur and the fixtures will not wor

2Table of contents1. Safety instructions... 32.O

20- The number of the hours that the COLOR SPOT 150 has been powered On since thecounter was last reset.Press [ ] or [ ] to return to the menu.I

21 - Pan reverseThis function allows you to invert the pan movement. Use the [ ] or [ ] buttons to select "On" if you wish thisfeature

22 - Display -intensityWith this function you can adjust the display intensity from 20% to 100% . Use the [ ] or [ ]buttons to select the level of

239.5 Test sequencesThis function allows you to run a special demo-test sequences without an external controller, which will show yousome possibilitie

249.6 Stand-alone settingThis menu offers options for stand-alone mode as a selection of the playing program,programming and modifyingcurrent programs

25- Editing programThis menu item allows you to select a program to edit or create.The COLOR SPOT 150 has one built-in program("tESt") and

26 - Manual control of effectsThe function allows you to control manually the channel functions of the fixture. Use the [ ] or [ ] buttons toselec

271. Calibration via the control panelPress [ ] and the [ ] or [ ] buttons in order to display the following messages: "Colo, rGob," f

28main PCB).The yoke is not located in the default position after the reset.ti.Er.(TILT-head movement error) This message will appear after the reset

29Shutter/Dimmer:- Simple dimmer from 0 - 100 %Motors:- 5 high quality stepping-motors controlled by microprocessorsFans:- Two axial fans - one in th

3CAUTION!Keep this device away from rain and moisture!Unplug mains lead before opening the housing!FOR YOUR OWN SAFETY, PLEASE READ THIS USER MANUAL C

3012. Maintenance and cleaningThe operator has to make sure that safety-relating and machine-technical installations are inspected by an expertafter e

31operations are only to be carried out by authorized dealers.Please refer to the instructions under "Fitting/Exchanging the lamp".Replacing

42.Operating determinationsThis device is a moving-head spot for creating decorative effects and was designed for indoor use only.This device is desi

53.Description of the deviceRear panel of the base12 - Display13 - Mode-button14 - Enter-button15 - Up-button16 - Down-button 6 - DMX output 9 - Fus

64.Installation4.1Fitting/Exchanging the lampDANGER ! Install the lamp with the device switched off only.Unplug from mains before !To insert the lam

7To reduce a hot-spot, pull the lamp in by turning all three screws „A, B, C” clockwise 1/4-turn at a time until thelight is evenly distributed.If the

84.4 RiggingDANGER TO LIFE!Please consider the respective national norms during the installation!Theinstallation must only be carried out by an author

9The moving-head can be placed directly on the stage floor or rigged in any orientation on a truss without alteringits operation characteristics .Ther